About LEDS Light
About LEDS Light
About LEDS Light
The LED consists of a chip of semiconducting material doped with impurities to create a p-n junction. As in other diodes, current flows easily from the p-side, or anode, to the n-side, or cathode, but not in the reverse direction. Charge-carrierselectrons and holesflow into the junction from electrodes with different voltages. When an electron meets a hole, it falls into a lower energy level, and releases energy in the form of a photon. where to buy cheap LED Strip?
Lightereryday is a good choice. The wavelength of the light emitted, and thus its color depends on the band gap energy of the materials forming the p-n junction. In silicon or germanium diodes, the electrons and holes recombine by a non-radiative transition which produces no optical emission, because these are indirect band gap materials.
The materials used for the LED have a direct band gap with energies corresponding to near-infrared, visible or near-ultraviolet light. LED development began with infrared and red devices made with gallium arsenide. Advances in materials science have enabled making devices with ever-shorter wavelengths, emitting light in a variety of colors.
LEDs are usually built on an n-type substrate, with an electrode attached to the p-type layer deposited on its surface. P-type substrates, while less common, occur as well. Many commercial LEDs, especially GaN/InGaN, also use sapphire substrate. Most materials used for LED production have very high refractive indices.
This means that much light will be reflected back into the material at the material/air surface interface. Thus, light extraction in LEDs is an important aspect of LED production, subject to much research and development Bare uncoated semiconductors such as silicon exhibit a very high refractive index relative to open air, which prevents passage of photons at sharp angles relative to the air-contacting surface of the semiconductor.
This property affects both the light-emission efficiency of LEDs as well as the light-absorption efficiency of photovoltaic cells. The refractive index of silicon is 4.24, while air is 1.00002926 recommend directory: 5050 SMD Flexible Strip with waterproof 5 Meter 150 LEDS. Generally a flat-surfaced uncoated LED semiconductor chip will only emit light perpendicular to the semiconductor's surface, and a few degrees to the side, in a cone shape referred to as the light cone, cone of light, or the escape cone.
The maximum angle of incidence is referred to as the critical angle. When this angle is exceeded photons no longer penetrate the semiconductor, but are instead reflected both internally inside the semiconductor crystal, and externally off the surface of the crystal as if it were a mirror. Internal reflections can escape through other crystalline faces, if the incidence angle is low enough and the crystal is sufficiently transparent to not re-absorb the photon emission.
But for a simple square LED with 90-degree angled surfaces on all sides, the faces all act as equal angle mirrors. In this case the light can not escape and is lost as waste heat in the crystal. A convoluted chip surface with angled facets similar to a jewel or fresnel lens can increase light output by allowing light to be emitted perpendicular to the chip surface while far to the sides of the photon emission point.
The ideal shape of a semiconductor with maximum light output would be a microsphere with the photon emission occurring at the exact center, with electrodes penetrating to the center to contact at the emission point. All light rays emanating from the center would be perpendicular to the entire surface of the sphere, resulting in no internal reflections.
A hemispherical semiconductor would also work, with the flat back-surface serving as a mirror to back-scattered photons. Many LED semiconductor chips are potted in clear or colored molded plastic shells. The plastic shell has three purposes:Mounting the semiconductor chip in devices is easier to accomplish.
The tiny fragile electrical wiring is physically supported and protected from damage The plastic acts as a refractive intermediary between the relatively high-index semiconductor andThe third feature helps to boost the light emission from the semiconductor by acting as a diffusing lens, allowing light to be emitted at a much higher angle of incidence from the light cone, than the bare chip is able to emit alone. recommend directory: 5050 SMD Flexible Strip with non-waterproof 5 Meter 300 LEDS
.
Top 5 Tablets Now in the World - the Beginning of Dual-Core War Free Tmj No More Program A nice Coach bag Nice Prescription Eyeglasses are quite Popular Prime 5 Stability Program Create Three Achievement Ideas To Developing A Rewarding Jusuru Company What is a fair-faced concrete Second Time Round the Block Personal Responsibility: Lessons From Japan Ping G15 Irons Compared to Ping G10 Irons Does Subliminal Mp3s Work Genf20 Plus The Modern Fountain of Youth The Cement tank: The Best suited Means to fix Cement Related Ecological Concerns