How to Do Basic Home Repair Like Raising a Sunken Floor

Author: Glenn Gehrke

Author: Glenn Gehrke

Many a home owner can save tons of money by doing the work themselves. All they need is a little guidance in the right areas. Take a sagging floor for instance. You might think leveling it is out of your league and too hard to do. It is really no too difficult for you to accomplish if you are willing to do a little work. It is generally suspended in the air atop posts and beams. All you have to do is lift it off the posts with jacks and replace the posts with longer ones. Now the scope of this article is not able to cover a sunken concrete floor. That is an entirely different matter. Let's get to the sunken wooden floor. Under it is either a crawl space or maybe a basement and you would need to determine where the floor is sunken to be able to find the support member that needs to be repaired. This is pretty easy to do with a level. Go to the room that has the most noticeable lean in the floor and lay the level on it to see which direction the floor falls. Now go all around the room and lay the level in different directions to find the lowest point. Sometimes the lowest point is in a different room but it is pointing to where the repair needs to take place. Some of the causes of sinking are rotted wooden members that support the floor, the concrete or stone pier has sunken into soft earth possible from having the soil under the pier being disturbed during excavation and not getting it compacted before placing the pier or there was a shift in the earth below and it cause an area of the house to sink. All of these causes can be fixed so do not despair. There are simple and easy to apply steps you can take to do the job yourself. The main tools you will need are;

* 25 ton or bigger jacks (you should have two of them. You can get away with 12 ton jacks but it is harder to pump them.) Or house screw jacks.

* Pressure treated lumber for new posts like 4X4 or 4X6 to go under the beam and down to the concrete pier.

* Some 2X4 pieces to nail the posts to the beams when done or metal straps if you like.

* A hammer,

* A sledge hammer,

* 4 two foot pieces of 2X6

* 2 pieces of 1'X1' 3/4" plywood for the jacks to stand on.

* A good 4' or longer level

* clean plastic sheet to lay on under the house More home repair and remodeling information Now that you have all the tools ready and you have located the part of the house that is low. It is time to get to work. You will want to be close to the post when you jack up the beam. That way you are only lifting the low end of the beam and not trying to lift the whole beam from the middle. Generally two beams meet over a post and you will need two jacks to safely lift each beams weight off of the post. To place the jacks properly you first lay down the 2X6 pieces side by side (2 of them) and then you lay the 3/4" plywood on top of them in the middle then the jack goes on top of that. This gives you a nice big footing to lift from. Make sure the platform you build is level. The jack has to be pointing straight up and down to work safely. The last thing you want is a leaning jack with a bunch of house weight sitting on it and it decides to fall over. Work safe and you will have a good time fixing the sunken floor. Now begin lifting the beam or beams up, If two beam ends are being lifted they need to go up at the same rate and height. Now go and check the floor periodically to make sure you are getting it level. You may hear some loud popping and creaking sounds. This is natural so don't be alarmed. If you have to lift the floor up more than 1/2 to 1" you may get some cracks in the walls and they are just cosmetic so they can be patched without too much difficulty. Doors may also not fit their openings if you had to lift a wall with a doorway in it. Once you have the floor level again give it a pump or two more on the jack and cut yourself a new post to fit the new gap from the beam to the concrete pier. Place a piece of tar paper on top of the concrete pier and then the new post on top of the tar paper so the wood cannot touch the concrete. This will prevent the wood from rotting. The wood should also be pressure treated. In some cases you have to lift the outside wall off the foundation to get the floor level. This is where a second person and two jacks and a temporary beam are needed. The beam is placed under several of the floor joists (perpendicular) and used to lift all of the floor joists at the same time so the repair can be done at the perimeter foundation. If there are two beams make sure the joint lands in the center of the new post and then lower the beams to the post. Now take the 2X4 pieces and lay them against the beam and down each side of the post and nail them together. You are now done and can pick up all your tools. Before you pack up go make sure the floor is level and you are satisfied. When you are happy with the work put the tools away. If you are lifting beams in a basement you would use pole jacks for safety and ease of use. You still want to build the wooden base for the jacks to stand on so you don't take a chance of cracking the concrete floor.About the Author:

I really enjoy writing about several subjects that I have activities in. That way I get to convey my knowledge to many many different people so they can get benefit from the knowledge.

Do check out my blog on remodeling and home repair http://www.newlinepubs.com/blog

POST COMMENT

Get Bad Credit Home Refinance With Easy Terms Small But Important Tips To Be A Super Work From Home Mom Open Vent System Boilers Home Additions Smart Ideas for Bathroom Renovation Fast Delivery On Bauhaus Furniture From Home Concept The Benefits Of Doing Clerical Work From Home What Are The Skills Required For Clerical Work From Home? Capture the Old World Charm of Spain In Your New Kitchen Design! Lose Abdominal Fat - How to Get a Flat Tight Stomach Quick With These Tips to Flatten the Stomach Over The Sink Colander - A Good Use In The Kitchen Leasing A Remodeling Contractor Avoiding Predatory Manufactured Home Loan Lenders