Rotary standard glass of cold adhesive labeling machine fault diagnosis - labeling machine - screen printing industry, especially

Rotary standard glass of cold adhesive labeling machine fault diagnosis - labeling machine - screen printing industry, especially

At present, most of the brewery, winery, wineries and some potent beverage plants, seasoning the bagging plant to run a workshop for the use of labeling machine cold glue paper to the glass paste the subject of rotary labeler. This article on how the situation under the sign pasted to determine the reasons for the failure to provide readers with some reference of tips.

Test run was good or bad labeling machine standards is to see the most direct labeling machine back out from the label on the bottle whether the paste was normal. In the production process, in addition to the daily management of the machine, the machine operators and managers should be regularly exported to the labeler conveyor belt next to the container, check the bottle label conditions.

Normal circumstances, the bottle on the label there are three major categories of abnormal conditions: periodic failure, continuous failure, accidental failure.

1, periodic failure Periodic failure is the number of containers will appear separated by the same labeling conditions are not normal. Periodic failures occur because a label in a particular device or a transmission device of a certain piece appeared abnormal symptoms, according to this line of thought can find the parts in question.

1, body marked damage Body marked cyclical symptoms in most cases the damage is due to the roulette-wheel exports caused. Specifically, exports of the last round of star wheel disk groove in one or a few cracks have appeared, a thorn, deformation, wear and so on, which will be torn, scratched, wrinkled, target the upper body collision ; Similarly, the export-wheel disc in the next one or several grooves will be damaged by the problems in the subject of the lower body. In addition, foreign body between the upper and lower wheel will damage the body labels. Typically, the back labels smaller than the standard body, therefore, be exported back-wheel disc marked the possibility of damage to a small number.

2, tag tilt Periodic label tilt symptoms in most cases is marked by a grasp of some drum parts caused by the above. Some parts can find from the following reasons:

? Grasp Pad Standard folder that the following conditions or abnormal regulation. For example: pads have wear; pads and the gap between the standard palm is too big or too small; pads can not be that good with the other folders.

? Arrested standard folder that glue glue or regulate abnormal. For example: a folder that can clamp the label, the other folders that can not grip the label; folder that is not in the center of standard palm grooves; folder refers to open or close the time is incorrect; folder that can not be a good match with the pads, etc. .

? Sponge Pushing glue glue or wear, deformation.

? A grasp of a standard folder that the folder that spring has broken or stuck.

? Labeling station cardan shaft assembly is not correct, that is, universal axis is not labeled.

3, label side of the non-gel

Periodic label side of the non-gel symptoms (commonly known as: Yin and Yang), and will in most cases is taken as a standard of a standard charge of some of the errors caused. You can find from the following several reasons:

? Standard charge of not properly label roll label box front end. For example: standard palm forward or backward roll; standard palm side of the hydraulic pressure on the labels do not.

? Standard palm palm is not clean. For example: Standard glue palm side of the dirt and other insoluble glue.

? Standard palm has been damaged. For example: a deformed, wear.

4, label-free plastic corner Cyclical symptoms with non-gel label corner of the label side of the periodic symptoms are basically the same without glue, in most cases is due to take charge of standard marked the deformation caused by wear and tear. Deformation is the bending of a corner, a corner of the mill wear is bald.

Concerned about changes in business innovation process management to find new ideas?? Command of the 2010 special screen printing industry of China Development Forum

"Zhen Xing Cup" 2009 China Top Ten selection screen printing special awards ceremony

More exciting, please see>>

POST COMMENT

How To Computer Data Recovery :Backup Data Properly Good Use Of Your Laptop AC Adapter --- tips from www.go-shop.com.au Some Tips to Troubleshoot an HP Printer How to Maintain Your Printer How to Change a DC Adapter for a Laptop -- go-shop.com.au Slow Computer? What Might Be to Blame Uninstall/Remove Pest Detector 4.1 and Stop Your Computer From Freezing Waiting on Your Computer? Find Out What Could Be Wrong Mickey Mouse Invitations For Kids The Extremely High Cost Of Getting Pregnant With Drugs And IVF Programs How To Make Her Orgasm With Cunnilingus - This Is So Simple That A Computer Nerd Can Do It Why Affiliate Programs Continue To Be the Perfect Work At Home Jobs Debt Settlement Relief Programs - Do They Make Financial Sense For Me?