Washing Machine Maintenance, Noise Cancellation And Laundry Common Sense - Washing Machine, White,

Washing machines long-term disabled, to exclude water

, to keep clean.

(2) should be placed in dry, non-corrosive gases, no acid and alkali erosion of places to prevent rusting of metal parts, electrical components reduce the insulation properties.

(3) there is no note on the wave axle hole of the washing machine, washing machine oiling should be given time to prevent corrosion.

(4) long-term storage of the washing machine should be covered with plastic film or Covers, to avoid dust, erosion, maintaining washing machines bright and clean.

(5) separated 23 months to start trial operation, to prevent rusting components,

Motor Winding damp. Winding power is a means of drying can be disabled to avoid too long and cause damage.

(6) washing machine not long in direct sunlight, especially for plastic devices to prevent fading, aging.

Reasons for excessive washing machine noise

Washing machine noise is too large, even the sound of impact because of the following areas:

1. Washing machine installation injustice. Automatic washing machine is more important, be sure to select the ground, adjusted the level of position.

2. Electric motor Bearing Or shaft with bearings badly worn or cracked. Automatic washing machine

Gear The gear box failure. 3. Belt too tight. 4. Pulsator deformation and laundry bucket bottom friction.

5. Dehydration barrel outside the box hit.

6. Shaft seal on the tight.

7. Certain parts of the Fastener Loose. 8. Automatic washing machine drum balance boom set to lose balance, to be replaced or adjusted

Spring . Reasons for excessive washing machine noise

Washing machine noise is too large, even the sound of impact because of the following areas:

1. Washing machine installation injustice. Automatic washing machine is more important, be sure to select the ground, tuning the horizontal position.

2. Motor bearings or the shaft with bearings badly worn or cracked. Automatic washing machine gear box gear failure.

3. Belt too tight. 4. Pulsator deformation and laundry bucket bottom friction.

5. Dehydration barrel outside the box hit.

6. Shaft seal on the tight.

7. A part of the fastener loose.

8. The balance of automatic washing machine drum boom set to lose balance, replace or adjust the springs.

How to reduce vibration and noise of washing machines

Washing machine after prolonged use, due to mechanical wear and tear, lack of lubricating oil, machine aging, spring fatigue deformation and other reasons, there will be a variety of abnormal vibration and noise. If timely repair, washing machine parts will lead to accelerated wear or damage. In fact, by appropriate adjustment and simple repairs that can eliminate or reduce the vibration and noise.

1, laundry, the body issued a "pop" sound. The failure over the laundry bucket and a collision between the shell or the washing machine is not placed flat on the ground or 4 feet is not a good contact with the ground. Then take the washing machine center of gravity adjustment, place the smooth, or four pads on the bottom right pads.

2, laundry, the pulsator turn issued a "giggle" friction sound. Maintenance, they can into the water, without letting go of clothing to be checked. Pulsator rotation at this time if there are still "gurgling" sound of friction, that is, with the laundry because pulsator rotating the bottom of a barrel caused by friction, such as further into the clothing, the sound will be even greater. Failure may be due to loose screw pulsator, the pulsator can now demolished, and then add in the shaft at the bottom right pad thickness of washers to increase the pulsator and the barrel end of the gap. Elimination of collision or friction between the two. If pulsator outer grazing laundry bucket, pulsator should be removed, repaired and then re-installed.

3, motor rotation, the rotating belt issue of "crack" sound. The failure is due to relaxation caused by belt drive. Maintenance, can be the motor housing of the fastening screws loosen, the motor direction of rotation to the axle away from the waves, so that drive belt taut, and then base the fastening screws tighten.

Washing machine is what causes leakage

Washing machine is working under humid conditions, once the washing machine internal electrical parts or wiring damaged or water soaked, washing machines, insulation would be damaged, leading to leakage, in addition to static electricity are also often occur with the induction Therefore, once found live phenomenon, should be down to check.

1, the barrel of liquid charged. This is the pulsator shaft and charged multi-site linked through cause and should focus on examination of barrels of insulation under the circumstances and electrical parts water leakage, up until troubleshooting.

2, shell charged. Charged shell should check whether there is skin damage the power cord,

Copper Line exposed and find out the leakage site after the application of insulating tape wrapped. Some capacitors are damaged, replace capacitors.

3, caused by electromagnetic induction sensor power. At this time, even if the washing machine insulated well, also measured with a test pencil glow phenomenon. Induction of electric energy is usually small, not

Personal safety Cause harm, to eliminate electrical induction as follows: First, the ground wire connected and washing machine; second swap power supply ground wire hole, the original hole inserts into ground Firewire plug hole to change.

4, static electricity is a washing machine the results of electrostatic induction, greater energy, serious people who will give a strong shock, there are two ways to eliminate static electricity, one to replace belt or pulley; Second, the belt in water immersed for 2 hours, taken out of dry water, can be re-installed.

by: gaga

POST COMMENT

Import static pressure bearing of Some experience in maintenance - bearing, hydrostatic bearing imports, maintenance - construction machinery industry Meet The Leading Company In The Field Of Aircraft Maintenance Conservation of natural stone stone rust prevention and control - stone, maintenance - Building Materials Industry Facts About Lawn Maintenance That You Should Know Pelleting machine maintenance and maintenance - pellet mill - the pharmaceutical industries Siemens Takes Over Maintenance Of Radomiro Tomic Mine Crusher And Belt System Proper Cabinet Maintenance The Key To Longevity Common Mistakes To Avoid In Maintenance Of Wooden Gates General Maintenance Issues Usage And Maintenance Of Stainless Steel Cookware Do tires need maintenance? Acceptance Testing And Maintenance Of Power Transformer It's Best to Take On Your Car's Maintenance In Phases