subject: How To Free Up Space In The Kitchen [print this page] And the kitchen is the most complex and are often used as a workshop in most homes, and in order to make that workshop as efficient as possible, it is important to have the tools to trade well organized and easily accessible. There are a wide variety of kitchen organizing accessories are available for some brands of certain tanks and other designed to add to the coffers of standard units.
But you can make your accessories, too, is specially designed to suit your needs. This article explains how to build a joint Kitchen Accessories that will add storage space and help you organize your kitchen better.
Before you start to build more storage space in your kitchen, first you need to know what needs to be stored. Whether you are adding space for pots and pans, dishes and glassware, trays, plates, service, and spices or canned foods, the first step is to measure the applied you need to be stored until you know how big to build your storage units.
In this document you will find information on:
Store pots and pans *
* Serving trays and pans
* Dishes and Glassware
Pots and pans storage
* Pots and pans are among the tools the "most difficult" to store because it comes in a wide range of shapes and sizes. One way to increase the storage cabinet is through the addition of panels Pegboard into the cabinet doors to hang the most common ponds, and storage cabinet with maximum comfort shelves.
* Use the 4.1 "Pegboard for extra durability. If you have a choice between Pegboard standard or mood, and choose the mood that it is more resistant to water.
* To build Pegboard door panels, and measuring both the first and open the doors, and panels Pegboard will have smaller than the door so as not to prevent them from closing. Cut panels, then mount them to the back of the wooden doors and bolts with commas. Pre-separators that are available from retailers who Pegboard hooks shares. And commas Group held away from the door so you can insert hooks Pegboard.
* If you have a cabinet doors magnetic disc or hunting, rather than to stop the self-closing, you may need to replace the existing joints with self-closing stop. This way you can completely remove the catch. If you decide not to replace the stops, you will need to remove the catches to install the panels Pegboard. Went a second time and realized the bottom of the Pegboard and on the floor of the Council of Ministers.
* Build your own comfort shelves to be deep enough to accommodate the larger number of ponds that will be set it up, but narrow enough that it will not intervene in pans hanging on the insides of the doors. Upon them, the first four criteria Mount Shelf on both sides of the Council of Ministers. Standards must be developed 02/01 "from the back wall of the Council of Ministers, and 1 / 2" from the cliff face. You can also install them, check them level to make sure it is plumb and the openings in each of the four criteria are level with each other.
* Then measure the distance from the face of the standard to meet the level of the opposite. Reduce your shelves 1.4 "shorter than this measurement to install the shelf. Footage on the standards, then put on the shelves in place. Modified when necessary to provide about 1" clearance between the tops of pans, bottom shelf next.
* The second strategy for storing pans is to build the panels Pegboard vertical slide inside and outside of the cabinet and hang pots and pans on them. The use of 1x2s or 1x1s (actual size is 3.4 "square) and a runner at the top and bottom of the Council of Ministers.
* Make sure the space for the paintings so that there is plenty of room for the pans you plan to store. Install the bottom runners first, gluing and screwing them call the Council of Ministers so that there is about a gap "between the 08/03. Then use the level of animosity toward the top mark just above the bottom runners.
* If necessary, 1x2s linked horizontally in front and rear cabinet to attach the top runners were stationed. It should be stationed with the level of the upper part of the door opening. Glue and screw the top runners in place as it did in the summer of the bottom, and the runners should project to open the door.
* Measure the vertical distance from the cleats on the ground to the Council of Ministers, then measure from the back of the cabinet to the front. Put cut 4.1 "from each dimension and 1.4 boards Pegboard" for this dimension. Slide plates in place and hang your pans.
