subject: Ideal TR1000 digital composite machine error code description - office supplies industry [print this page] Ideal TR1000 digital composite machine error code description - office supplies industry
E02 motor locked down and disconnect the machine is running a show in the start-up input tray lift motor 9 seconds, the maximum lift position sensor does not lift the action block 2, starting at the lower input tray lift motor 9 seconds , the down limit position sensor is not blocked the action block 3, in lifting up the tray motor start within 2 seconds, lifting lower level sensor is not blocked the action block 4, in lowering the tray lifting motor start within 2 seconds , lifting lower level sensor block the action is still up The first version of the folder
e03 fault indication interrupt the machine running 1 version of the folder coil activated (connected to) 4 seconds, folder security version is still depressed at the beginning of the movement block 2, the coil plate clamp release (off) 4 seconds, folder security version is still depressed at the beginning of the movement block 3, in the version folder 8 seconds after the motor starts to rotate, the angle sensor (0 degrees and 180 degrees) angle of the magnet 4 is not detected, not in the version folder coil operation , folder security version of action block was not depressed
E04 ink overflow display and overflow interrupt the machine operation in the extrusion devices of ink sensor detects too much ink
E05 motor locked the printing position in the printing position motor to rotate button within 12 seconds, if the vertical center sensor state is not from the "links" into "off" or "off" switch to "pass"
E06 pressure sensor failure detection and interruption of machine operation show that the main motor starts to rotate after 8 seconds, if not from the pressure detection sensor status links "into" off "or" off "switch to" pass "
E07 (only ra59) ra and ra editorial board communication failure and interruption of machine operation show that if the cpu and ra edit communication error between the
E08ra communication failure occurred and the computer interface display and interrupt the machine operation if the cpu and the computer interface communication error between the
E09ra and with page display and communication failures between the interruption of machine operation if the cpu and the communication between machines with page error
E10 (only ra59) shows interruption of machine operation and image scanning operation in the beginning, if the data signals (such as the original format, etc.) are not from the slit output circuit board
E11 lock pressure control motor and disconnect the machine is running a show in the pressure control inside the motor starts spinning 100ms, not detected from the pressure control motor encoding disc sent pulse 2, the pressure control within 5ms motor starts spinning, intermediate pressure sensor state is not converted from a pass off (or turn from the off Chengtong)
E12 Select the error display state machine and stop the machine running the system board switch sw2 (hex switch) is set in the "unused" state
E13 trimmer motor was locked and the machine displayed at the plate and break the machine is running secret operations in the cutting operation, the location of a roller, the plate position sensors detect the plate, but in the second cut After the operation, the drum once again to place a position sensor when the plate was still detected in plate
E14 second edition folder failure folder in the version of the coil is not in operational state, the action plate clamp block safety switches are not depressed
E15 (only ra59) platform read lock pulse motor show and interrupt the machine to run 1, the platform read pulse motor activated 18 898 pulses, the image scanning device position sensor does not detect the initial image scanning device 2 in the platform read pulse motor activation after 15 748 pulses, image scanning device automatic document feeder darkened image sensor scanning device is not detected 3, the platform read pulse 314 pulse motor activated, the image scanning device is not from Image scanning device position sensor on the release of the initial opening 4, the platform read pulse 314 pulse motor activated, the image scanning device is not the initial position from the image scanner automatic document feeder darkened release sensor open
E16 c sensor failure display position and disconnect the machine run 1, the main motor starts to rotate eight seconds position c sensor status does not convert from the pass off (or turn from the off Chengtong
E17 will replace the battery display and interrupt the machine operation if the following three kinds of cases, the battery detection signal is still "off" (1) When the machine power on (2) when you press the "Restore all" button (3) the end of the machine into operation
E18 with Page Fault Display and break the machine is running received from the device with the error code page
E19 hot motor lock and break the machine is running a show in the thermal print head pressure motor thermal activation down 4 seconds after the first thermal print head pressure switch is not depressed 2, the thermal print head pressure Motor thermal activation up 4 seconds after the first thermal print head pressure switch has not been released
E20 wing board motor lock and break the machine is running a show in the wing plate motor activated within 5 seconds, jump wing panel has not been depressed at the beginning of sw1 or sw2 2 activation in the wing plate motor 5 seconds, jump wing panel switch sw1 or sw2 is not released
