subject: Real-world tips for hanging doors [print this page] Real-world tips for hanging doors Real-world tips for hanging doors
Shim before the door goes in
The usual method of holding the door frame in place while you shim behind
the hinge side .is awkward. It's a lot easier to shim the hinge side of the rough opening before you put in lhe door frame. Aflor lhal, it's a simple joh lo sot the frame in place, screw or nail it to tho shims, and then shim tho strike side. Measure lho width of the rough opening before you start shimming to see bow much shim space is available. Usually the rough opening allows for about 1/2 in. of shimming on each side of tho frame. lf the rough opening is extra wide, you can use fewer shims by tacking scraps of 1/2-in. plywood at the hinge locations firsl, and then add shims to plumb the jamb.
SHIM THE EASY WAY: Mark the location of the hinges on the drywall alongside the opening so you'll know where to place the shims. Place shims at the top and bottom hinge locationsusing a long level or a straight board and a short level. Then add the center shims.
Make sure your exterior door clears the rug
Most of the time, you can simply set your new exterior door frame directly on the subfloor and the door will easily clear carpeting or a throw rug. But if you're replacing an old door with a thick sill, or if the floor will be built up with tile, thick carpet or an extra layer of wood, you could have a problem. And there's no easy solution after the door is installed. You can't simply trim the bottom, because then the door won't seal against the sill. To avoid this problem, add a spacer under the door before you install it. The key is to determine where the top of the tile, carpet or throw rug will be, and then raise the door frame to leave about a 1/2-in. space under the door.
AVOID CLEARANCE PROBLEMS: Screw a strip of plywood to the bottom of the rough opening to raise the door and prevent It from rubbing on the floor Inside.
Set interior jambs on spacers
If you set the doorjambs directly on the subfloor, there's a good chance the door will rub against the carpet later. Of course, you can cut off the bottom of the doors, but it's easy to avoid this extra work by planning ahead. Find out the thickness of the finish floor and then calculate where the bottom of the door will be. Plan the installation so there will be about 1/2 to 3/4 in. of space under the door. Usually setting the doorjambs on scraps of 3/8- to 1/2-in.-thick trim will put the door at the correct height. Can help you monitor the temperature Honeywell Thermostat Manual.
HIDE THE SCREWS: Pull back or remove the weather strip on the latch side of the door frame and drive screws where they'll be hidden.
Hidden screws make exterior doors stronger
There are many benefits to using screws rather than nails to install exterior doors. They can be adjusted and won't easily pull out or loosen. But you don't want to leave the painter with the task of filling big, ugly screw holes. The trick is to hide the screws under tho weather stripping on the latch side. On the hinge side, you can simply replace one screw in each hinge with a matching 3-in.-long screw. Always start by drilling a clearance hole that allows the screw to slide freely in and out of the hole. This ensures the screw will pull the jamb tight to the shims, and allows for adjustment if needed. Don't let the spinning screw rub against the weather strip-it will slice right through. I know this from bitter experience.
AVOID TRIMMING DOOR BOTTOMS: Raise doorjambs with scraps of trim to make sure the door will clear the carpeting.
Tune up the rough opening
Twisted or out-of-plumb rough openings raise havoc with door installations. If you install the jambs to follow the walls, the door is likely to swing open or shut on its own. On the other hand, if you plumb the jambs against the outof-plumb rough opening, the trim will be hard to install. As long as the bottom of the wall isn't held in place by flooring, there's a simple solution. Just move the studs on both sides of the opening back to plumb. Don't think you can do this with your trim hammer, though. You'll need a maul or a sledgehammer.
1 CHECK FOR PLUMB: Check both sides of the door opening. If they're more than 114 in. out of plumb, adjust them before you install the door.
2 NUDGE THE WALL: Protect the wall with a 2x4 scrap while you move the bottom of the wall over with a sledgehammer. When the wall is plumb, toe-screw the bottom plate to the floor to hold it in place.
Trim the bottom to level the top
Old houses are notorious for having sloping floors. Even some newer houses settle in unexpected ways. If you don't cut the jamb to compensate for the out-of-level floor, you could have a problem getting an even space between the top of the door and the head jamb. This is critical if you're installing a door over existing flooring where the jambs have to fit tightly to the floor.
Hide screws behind the hinges
Screws are better for securing the hinge jamb because nails can work loose. You can easily replace one of the short hinge screws with a long screw. but it can be difficult to find a strong screw that matches the other screws. Here's a trick we learned. Hide tho screw behind the hinge. Tt only lakes a minute or two to remove all the hinges and gain access to this area. Then you can drive a self-drilling screw through the jamb wilh ease. Make sure the jamb is straight and plumb before you reinstall the hinges.
