subject: Konica Composite Aircraft Maintenance Professional Answering Service [print this page] Konica fault code and the simulator solution
J11 for paper jams paper jams PS1 J16 for feeding cardboard PS PS2 J31
J32 cardboard paper outlet connection failure PS7 P20 P25 drum components need to add toner
P26 PM After clearing the counter, TDS did not tune P81 Key counter
Self-diagnosis code F09 leakage detection method with 25 write 0 to P49 Address
F23 Fault supplement powder off the main switch
F26 Toner concentration detector TDS fault code 51 with 47 ways to automatically adjust the TDS 3 minutes
F28 with 25 high-voltage power failure mode write 0 to P45 Address
F34 Fuser temperature failure mode with 25 write 0 to P47 Address
F35 Fuser low temperature failure mode with 25 write 0 to P47 Address
F36 Fuser temperature control circuit open way with 25, write 0 to P47 Address
F41 optical body to return failure
F42 optical body forward fault F43 exposing light failure F45 Lens drive failure F54 Cooling Fan Trouble F88 AE automatically adjust failure 25 Preferences way: Turn on the power of 25 the same time, use the number keys to enter address data, press P key, use the number keys to enter the required number of addresses, press P key, use the number keys to enter new data, press the Copy button
04 PTC heater within the range of 01 standard -00 = No 1 = a
11 counter selection 05 standard = 00 = 5 = total number of copy count
12 to heat the temperature range 0-2 to set the standard = 00 = 160 degrees 1 = 2 = 195 degrees 180 degrees
27 PM cycle to set the standard range of 0-9 = 3
28 PM cycle to set the standard range of 0-9 = 0
47 Fuser failure to eliminate the standard range of 0-9 = 0 1-9 = 0 = Clear Fault
48 0-1 automatically reset the time to set the scope of the standard = 1 0 = No 1 = manual reset 90 seconds
49 standard eliminate leakage fault coverage = 00 = 0-1 1 = failure to eliminate
50 A3 copying the standard two-count setting range 0-1 and 1 = 0 0 = 1 = Total 2
60 user bias shift range of 0-3 to set the standard = 0 0 =- 150V 1 =- 180V 2 =- 200V3 =- 130V
62 automatic power off time setting the standard range of 0-3 = 2 0 = 0 1 = 2 points 2 = 5 3 = 10 minutes
92 ways to immediately stop setting the standard range of 0-1 = 00 = 1 = does not immediately stop immediately stop
47 input and output inspection methods
By 47 while turning on the power, input signal inspection, with the number keys to enter an address code indicating HI or LO
Output signal checking, use the number keys to enter the address code, press the Copy button.
00 exposing light signal LO = HI = normal abnormal
01 for the powder electrical signal HI = YES LO = NO 02 charging power
03 04 separate high-pressure high-voltage transfer
11 Black 40V 12 imaging imaging bias the general bias
13 of 20 for paper, light imaging bias magnet HI = YES LO = NO
21 paper tailgate sensor signal HI = YES LO = NO 22 paper outlet sensor signal HI = YES, LO = NO
24 bypass for paper delivery paper solenoid electromagnet 25
29 separation claw solenoid 30 in situ optical sensor signal HI = YES LO = N
31 optical drive motor M2 40 M1 Main Motor
42 cooling fan motor M4 43 total counters
45 fuser heat lamp 48 operation panel lights all bright
49 CEL clean counter reset lights 90 PM
91 total counter reset 36 ways to adjust settings Using the number keys enter the required code by copying key, press the P key to enter new data, press the P key. Press the stop / eliminate input positive or negative adjustment of input light intensity of 90 press copy key, enter new data, the scope of 01 black? 64 Liang P key press
Paper at the front of time to adjust the input 91 by copying key, enter new data, range -10 slow? +10 Fast
Standard = 00 press P key Adjust the input rate of 93 vertical press copy key, enter new data, short-range -20? +20 Long
Standard = 00 press P key Lateral magnification adjustment input 95 by copying key, enter the new data range of -9? +9 = 00 press P key standards
Paper width adjustments to eliminate the first front-end by copying key input code range of 92 -9 little more than the standard = 00 +9 P key press
PM check and reset the counter and press P and 5 key to display counts PM
Enter 47, enter code 90, press the Copy button, the counter is reset
Check and reset drum counter by pressing P and the stop / clear key, display drum count
Into 7, enter code 91, press the Copy button, drum counter reset
Konica Composite Aircraft Maintenance Professional Answering Service
