subject: How To Replace A Kitchen Hood [print this page] And can be completed replacement of kitchen hood easily with a family member or friend. While you may wonder why any person to replace the cover of the kitchen, usually the answer is simple. For example, someone might want to update the appearance of the kitchen. Or someone may be replaced because it does not work correctly. In any case, here's how to replace the cover of the kitchen.
Tools
* A new kitchen range hood /
* Screws
* Screwdriver
* Friend
Wire nuts *
* The circuit tester
Warning: Remember that you are dealing with electricity, so far from the water, and use of all safety precautions issued by the manufacturer.
Step 1 - Turn off power
Remember to turn off power to the hood of the old kitchen. You will need to do so through the circuit breaker box. Wait 10-20 minutes and then test the wires with a test circuit to double check that you are providing any electricity to the hood of the kitchen.
Step 2 - Remove the old hood
After you know about the fact that it does not have electricity, you can begin the process of removing the hood the old kitchen. You must first stop the cover electrical wiring which is located by the light of the hard disk. And then a family member or friend hold the hood in the old kitchen when you are removing any screws or bolts of it. Once that is done, you can then slide freely run.
Step 3 - Verification of wiring
Double check that you have at least 12 inches of wire to connect the cover of your kitchen on the wall. It should be noted that if you have the hood of the kitchen without exits, proceed to Step 5 next.
Step 4 - Search for channels
If you have the cover of a new kitchen and exits, you will need to locate the fan or ventilation duct. Once you find it, you can open the vent hole where it will come back.
Step 5 - Wire
Open to cover the wires and put a cover in a safe area for easy access.
Step 6 - Install new kitchen hood
And your friend or loved one stand hood kitchen and on the occasion of the areas where the nails or screws will be. After that they put out the kitchen hood and screw in the middle of the road spikes in the holes. After that, you can slide in the hood kitchen.
Step 7 - Wire Road
Lightly pull the wires through the appropriate holes and connect each of the black wire from the hood of the new kitchen black wire from the wall with a wire nut. Then connect wires two white bonnet with the white wire from the wall, again using a wire nut. Next, connect the green wire to screw Green Earth. Place the wire and then cover again.
Step 8 - tighten screws
Finish tightening the screws in place.
Step 9 - Test
Check to make sure the fan and light work. If it is supposed to be vented outside, make sure that the air vent is left with no issues. If something does not work right, repeat steps 6 and 7 until everything works fine. Remember that you will be working with electrical equipment, and follow the safety measures issued by the State or the city.
* A new kitchen range hood /
* Screws
* Screwdriver
* Friend
Wire nuts *
* The circuit tester
Warning: Remember that you are dealing with electricity, so far from the water, and use of all safety precautions issued by the manufacturer.
Step 1 - Turn off power
Remember to turn off power to the hood of the old kitchen. You will need to do so through the circuit breaker box. Wait 10-20 minutes and then test the wires with a test circuit to double check that you are providing any electricity to the hood of the kitchen.
Step 2 - Remove the old hood
After you know about the fact that it does not have electricity, you can begin the process of removing the hood the old kitchen. You must first stop the cover electrical wiring which is located by the light of the hard disk. And then a family member or friend hold the hood in the old kitchen when you are removing any screws or bolts of it. Once that is done, you can then slide freely run.
Step 3 - Verification of wiring
Double check that you have at least 12 inches of wire to connect the cover of your kitchen on the wall. It should be noted that if you have the hood of the kitchen without exits, proceed to Step 5 next.
Step 4 - Search for channels
If you have the cover of a new kitchen and exits, you will need to locate the fan or ventilation duct. Once you find it, you can open the vent hole where it will come back.
Step 5 - Wire
Open to cover the wires and put a cover in a safe area for easy access.
Step 6 - Install new kitchen hood
And your friend or loved one stand hood kitchen and on the occasion of the areas where the nails or screws will be. After that they put out the kitchen hood and screw in the middle of the road spikes in the holes. After that, you can slide in the hood kitchen.
Step 7 - Wire Road
Lightly pull the wires through the appropriate holes and connect each of the black wire from the hood of the new kitchen black wire from the wall with a wire nut. Then connect wires two white bonnet with the white wire from the wall, again using a wire nut. Next, connect the green wire to screw Green Earth. Place the wire and then cover again.
Step 8 - tighten screws
Finish tightening the screws in place.
Step 9 - Test
Check to make sure the fan and light work. If it is supposed to be vented outside, make sure that the air vent is left with no issues. If something does not work right, repeat steps 6 and 7 until everything works fine. Remember that you will be working with electrical equipment, and follow the safety measures issued by the State or the city.
