Collar Machine Required: Offset Press Machine To Install A Few Notes
Collar Machine Required: Offset Press Machine To Install A Few Notes
1. Room size As Print Environment requires higher, and therefore the greater the room, the control environment of temperature and humidity the more difficult, from that point of view, the smaller the room the better. So for color Printing Equipment , The best stand-alone single-room, especially the multi-color machines should be so. But the room is smaller, the greater the noise, so little room to install the best muffler.
2. Chuang board position For printing the book version of Living Printing Equipment , Because the paper is quite soft and thus demanding Yan paper, it is generally in the machine or operation of surface area to one side of paper placed on press board, put the machine in place, they should leave enough room to board room Chuang .
3. Electrical box installation Electrical box is installed on the machine should be considered a major problem, its location should be the most safe place, that the machine utilization rate of the lowest around, so generally regarded its security drive in the machine side (Way points Some of the recent cases of people line the machine to power on the machine console box office, this Design Is clearly unreasonable. Electrical box and the alignment between the machine should be well protected, in addition to their increase snakeskin tube, the chamfer should be on the ground, buried the money, or use the wooden box to tying. Wires inside the machine should be well arranged, the use of clamps, must be clamping contact with the bad outlet to re-install. Workshop within the Power supply And electrical connections between the boxes using the above method should also be protected. In addition the machine itself to install and reliable ground must be, otherwise it will cause circuit malfunction, usually buried underground earth should be about 1m. To be safe, can be ground and connect the base of the machine. When the machine outlet short circuit or overload, if the machine's own protection equipment failure, external power supply will be undesirable impacts, so an external power supply protection circuit should be installed.
4. Pneumatic alignment Pneumatic alignment should also be seriously considered from the perspective of gas line, gas line as short as possible, so a small-capacity pump can be directly installed in the machine near the base. For large-capacity pump, because of its big noise and temperature rise, which should be placed far enough away from the machine number. If possible, would be a single building pumping stations, this is to reduce the noise, and it helps pump protection. From the pump to the machine in the vicinity of the tube with damping (such as steel) gas. But most of the pumping station should be as much as possible from the machine recently, did not advocate multiple machines share a pumping station.
5. Manifold Installation Asphalt is to install the machine to be considered an important issue, so when installing the machine, should carry out detailed examination of the oil circuit, oil must choose the right number, oil should meet requirements, where the best butter first hit it again butter, so to ensure reliable machine lubrication. For a long time without the machine should do so.
6. Machine security Security situation in the machine should be on the agenda from start to finish, there is an unsafe rule out hidden applications, if a time should be done can not be excluded under the record before the re-start rule. As always when debugging some parts of the machine is not considered comprehensive, such as paper sets down over the specified requirements, may result in damage to the chain or cause other accidents. Therefore, when installation of the machine is best carried out step by step instructions, and installation personnel should be in the best working condition.
7. Machine room built High precision printing press, so care must be exercised in moving machinery:
Do not let the machine carry on the way in collision with other objects, or light by the machine can not be installed on schedule, in serious cases can cause machine scrapped;
When lifting the machine, the machine's center of gravity should be as low as possible, so that it can remain stable in the handling process;
machine base application board pad up, do not use crowbars, steel pipe, jack directly in contact with the base, otherwise the contact surface will be damaged;
butt or looking at the machine level, each step should be carefully carried out, the joint part or would result in a collision, so that the relevant parts are damaged, so handling and installation personnel must have knowledge in this area and capacity.
The Benefits To Massage - My Opinion Forgotten Keys of the Kingdom World of warcract guide part 1 When Winning Is the Only Thing That Matters Managed Switches Can Be Managed A NASCAR Fan Club Check Your Moobs Dude Prostate Stimulation Methods Temper Tantrums - What Are They & The Best Way To Deal With Them Best Rated Q&A How to Choose an Appropriate Extracurricular Activity? When One Has Fear Of Flying Move Down To Clarify The Rumors Of The Acquisition Price Quoted Tencent Guess