How To Fit A Shower Head.

So your the one that has to do the work in the toilet

. Youngsters taking over the house and you tend not to have the room or its possible you've just managed the pay out for a new ensuite but have no capital left for the basics. Either way, connecting a shower neither be difficult or worrisome. The following information will give you an adequate amount of confidence to get going.

After you have acquired your shower you want to be sure that all of the products are there. Second of all you should investigate the warranty. The greater number of new showers have a guarantee for 2 years. Providers expect that a heavily used shower will survive at at a minimum 2 years. If the shower is second hand make sure that the shower head is altogether free of any kind of limescale. If it is you need to dedicate the extra effort applying some white vinegar to the nozzle ends. Failing this, set the head above a broiling kettle as this will confirm a clear filtration for the water. Shower heads are so low-priced no-a-days so you could possibly be much better of simply getting a completely new head.

As soon as you've inspected and rinsed the shower head the up coming step is to determine out where you will position it. By far the most normal place for a shower surround is in the corner of the cubicle. This is an apparent preference specifically if you have a compact or limited cubicle. The alternative benefit of using in the corner is that you you shouldn't have to be anxious about the handles impeding access to the cubicle without clipping the shower when getting in.

When you have identified the place you are intending to bring your new shower's water supply from, it's time to turn off the primary water source at the stopcock. Just in case there is water already in the pipework and to prevent water seapage, you have to turn on all the taps to run off any leftover water which is still in the system.

The initial thing you will need to do is get the piping ready. Just before fitting the pipes that will ultimately provide the water to the shower system, it is critical to cut off the water source. In order to defend the conduits, they should be provided a watertight masking and also isolating valves should be installed. The pipe joints can then be recessed into the retaining wall and covered over to neaten the overall look.

With the water turned down at the major stopcock and any remaining water purged from the system, you can commence running your pipework to the site of the new shower. You can use both plastic piping or copper mineral piping to run the water lines to the shower. Vinyl piping is easier for the DIY plumber to work with but you will need to be very careful to steer clear of leaks in plastic piping by fitting pipe inserts among joints and fit copper fittings at the ending of the pipework for improved trickle avoidance. Don't forget to fit separating valves at the end of the pipework as near to the shower as possible without being invasive or cosmetically unattractive. Separating valves might very well come in handy if your shower or pipework springs a leak. With an added water shut-off point close to your shower you will not need to rely as much on the primary water stopcock.

To prevent damaging thermostatic shower valves you should be certain that the pipework does not have any dirt or grit in it. Cleanse the pipework through to check this.

Measure where the shower valve will go

Keep the valve alongside the retaining wall and verify how much pipework length will be required to make certain the new thermostatic valve can fit flush.

Reduce the hot and cold water outlet pipes to the correct size. When you have confirmed how much pipework is required to fit the thermostatic shower valve you can cut the hot and cold water pipes for the shower using pipe blades.

Make the holes for the thermostatic valve

Drill the holes in the wall membrane to fit your thermostatic shower valve. If you are drilling into tiles make sure that your drill bit is suitable to work on tiling. Use a spirit level to fit any bracket or wall fitment flush to the wall to reduce challenges when fitting the shower valve and to prevent damaging tiling or plasterwork.

Fit compression olives into each of the h2o inlets

For further seapage prevention fit a compression setting olive and nip it up neatly.

Line up the shower valve

Level up the wall for the shower valve fitting taking care.

Fit the shower riser rail

Analyse how high you want the shower riser rail. Use a spirit level to tag vertically up the wall from the valve location to the elevation you would prefer the shower head to be. If in question, for additional assessment, stick masking tape to the wall vertically changing the spirit level and take it to the place where the shower head will be. Step back and check out that the shower head will be in the correct position using the masking tape as an indication of the shower riser track. As soon as you are confident that the shower riser rail is in the right position, cut the shower riser rail and run the pipework up the riser rail.

Fit the shower head to the riser rail and test for leaks

Checking Shower Thermostat Works

Make certain that the thermostat kicks in by turning on the hot and cold water taps when checking that the temperatures of your newly fitted shower stays constant as expected.

Make sure you have all of the instructions at hand and follow the instruction guide that will have been supplied if new. If the shower is 2nd hand have a look at the unit for anything important that you can search on Yahoo and google with. You will need to print this off as you will need to refer to it regularly throughout the setup process.

Step 1 Disconnect water and electrical supplies coming from the wall, leaving the electric powered and water supplies ready to connect to.

Step 2 Simply loosen the elbow fitting and retighten 90 anticlockwise.

Step 3 A template is provided that can be employed to verify details before any drilling starts.

Step 4 Briefly connect the T80z inlet onto the water supply and place the unit on the wall to tag the new bolt fixing areas.

Step 5 Drill down new holes and insert wall plugs ready to secure the T80z.

Step 6 Join the component onto the water supply and attach the device to the wall.

Step 7 Tighten the compression elbow onto the T80z inlet.

Step 8 Secure the inlet fitting with the two screws provided.

Step 10 Fit the earth conductor expansion bracket and earth extension wire.

Step 11 Place the provided insulating sleeves onto the live and neutral conductors.

Step 12 Hook up the extension cables using the provided terminal blocks.

Step 13 Secure the Uni-fit Kit bracket to the T80z with the screw supplied.

Step 14 Cut the extension cables onto the Uni-Fit Kit bracket and make final connections to the main terminal block and earth post.

Step 15 Connections accomplished using the Z Uni-Fit Kit.

Step 16 Temporarily fit the cover, select the cold setting and fill up the unit with water.

Step 17 Remove cover and place the pipe entry trims.

Step 18 Fit the start/stop switch connector in the cover.

Step 19 Line-up the front cover and fit the best and bottom fixing screws.

Step 20 Fit the riser kit and 5-mode rub clean showerhead to complete installation.

Finally fit the shower head and base tray. You should at this stage be able to Connect up the main shower control to the pipes that will be delivering the water.

The shower should now be ready for the screens and cubicle tray to be fitted.

Good luck. If your not the technical type can always consult your local plumber.

by: patyo8znbu

POST COMMENT

Steam Showers- How They Work. The Exhilaration Of Shower Pumps Ideas To Shape A Bridal Shower Tea Party In Summers At Classy Venues In London Make Your Life Colorful By The Led Shower How To Choose The Best Glass Shower Door Glass Shower Screens - Good-bye To Old Fashioned Molds Significance Of Shower Doors In Modern Bathrooms Shower Doors - Benefits Of Installing It Shower Enclosures Some Basics Tips To Choose The Best One Creating An Classy Shower Room Perfect Shower Room Creation In Bathroom Remodeling Selecting Shower Valves For Your Bathroom How To Choose The Ideal Glass Bathroom Shower Screen