Practical! Troubleshooting The Printer Of Four Feed - Feed Failure, The Printer - Screen Printing

Printer in the frequent use of the process, often appear unable to deal with the failure of paper

, mostly jammed, do not feed, one to go into more pages, and paper and behavior disorder. These failures occurred after the do?

1, the printer jammed and their solutions

1, printing paper surface is smooth. If the printer jams phenomenon, we must first see whether the flat surface of printing paper, paper curl or fold if the phenomenon is best used for flat surface, smooth paper, printing paper and to ensure that the surface can not have a similar type plastic attachments.

2, printing paper is too thin or too much. Must ensure that the quality of printing paper more than 60 grams or more, will cause the printer to print on paper is too thin when the going difficult on paper, likely to cause the printer jammed. And a load printing paper that is too thick.

3, the pickup roller wear. Pickup roller is most likely to wear laser printer parts. When inside the paper tray containing normal, but can not get paper, it often is to take the paper spring roll wear or loosening. Pressure is not enough, not of paper into the machine. Pickup roller wear, and sometimes can not be replaced when the rubber band approach can be used for emergency wound treatment. Wound rubber band, the increased friction rub paper, can feed back to normal.

4, other. Sheng tray is not properly installed, the paper of poor quality (too thin, too thick, wet), etc., also may cause paper jam or can not take the fault.

Second, do not feed the reasons and solutions

1, printing paper into too much. First check whether the installation of printing paper standards, such as whether the location is outside the printer into the left arrow symbol guide, if it does, must reduce the print paper.

2, blockage. Inside the printer to see whether there is any blockage, such as if the printer paper jam occurs, it would lead to the phenomenon into the paper. If a foreign body, then it must be to exclude, must first be ruled out when the printer power off, then carefully remove the foreign body. If you remove the paper jam, then, must be along the direction of the jammed paper slowly pulled out, remove paper jams even after the check for existence of residual scrap of paper, and to ensure that the shredded paper is also cleaned.

3, printing paper wet. If you use the print paper stored too long and the surface of the wet feeling, then there may be a phenomenon not feed at this time we have to do is to dry printing paper.

4, Ink Is used. If you are using inkjet printers, black ink or color ink cartridges direct bright light flashes or the ink will run out of tips. If the cartridge is empty, the printer will not feed.

3, one input, multiple pages, because there are 4

1, the location of printing paper. The location of printing paper placed incorrectly will lead to the occurrence of a multi-page and correct the paper can not be higher than the slot height of the arrow on the left side of guide signs; Secondly, check whether the use of printing paper size requirements: 60 ~ Weight 180 g of printing paper in order to meet requirements, while less than 60 grams of ultra-thin printing paper, it is also more prone to the phenomenon into the paper.

2, printing paper surface of coiled level. Curl also contributed to the occurrence of an input, multiple pages, this must ensure that the print paper, smooth surface, if a little bit curly, you can try to be it flat.

3, the impact of electrostatic induction. Also cause an electrostatic induction into the phenomenon of multi-page, must be installed before printing paper, printing paper first to spread out fan-shaped manner to ensure that each paper can be individually isolated, and then the right way to lead into the print paper paper slot.

4, adjust the location bar. For a paper thickness adjustment function of the printer, the adjust lever position is very important. In a different paper, the paper thickness lever position is not the same as, for example, the use of conventional thickness of printing paper, the need to adjust the location bar is set to "0." Of course, different printers on the regulation of standards regulating rod is not the same, the best reference manual.

4, printer paper, random walk When printing to a page of paper when suddenly a space walk and then go on automatically and then print. This is often prolonged use the printer, paper detection switch contacts due to wear and into the dust caused by poor contact, causing the printer to make a mistake to judge the reason. Open the printer, locate the paper detection switch carefully cleaned with alcohol, restore to normal.

by: gaga

POST COMMENT

Debt Relief Programs - The Better Alternative to Filing Bankruptcy Debt Reduction Programs - Why It's Easier to Negotiate a Debt Reduction Deal Now Introducing Memory Stick PRO DUO Why Offshore Companies Use White Label Debit Card Programs This Year's Total Grain Output Is Expected To Reach 33.3 Billion Kilograms - Of Food, Soy - Food Professional Film to DVD Transfer in Raleigh, NC Computer Glasses are given a Special Regard Nowadays Heater Product Quality Monitoring Yushchenko Panda Brands Heibang - Heater, Quality - Metal Industry Printer Sales Continue To Grow The World - The Printer, Dot Matrix Printers - Screen Printing Introducing Memory stick Zed Card Printing Considerations A Guide To Cheap Laptops King Of Shenzhou Liquid Crystal Computer Cost 1799 Yuan - Shenzhou, Desktop-it Industry