Steel Square - Party Laser Lights Manufacturer - China Full Color Laser Projector

Use in stair framing

Use in stair framing

Theoretical rise and run of stringer, placement of square, marking of tread and rise, dropping the stringer, ABC=90, total rise of stringer = 2R-T, total run of stringer = 2AB.

Stairs usually consist of three components. They are the stringer, the tread and the riser. The stringer is the structural member that carries the load of the staircase, the tread is the horizontal part that is stepped on, and the riser board is the vertical part which runs the width of the structure. There are many types of stairs: open, closed, fully housed, winding, and so on, to mention a few of them.

Laying out a staircase requires rudimentary math. There are numerous building codes to which staircases must conform. In an open area the designer can incorporate a more desirable staircase. In a confined area this becomes more challenging. In most staircases there is one more rise than there are treads.

The rise (vertical measurement), and the run (horizontal measurement). Note that the stringer will rest partially on the horizontal surface.

This is a two-by-twelve piece of lumber. A framing square is placed on the lumber so that the desired rise and tread marks meet the edge of the board. The outline of the square is traced. The square is slid up the board until the tread is placed on the mark and the process is repeated.

The board is cut along the dotted lines, and the top plumb cut and the bottom level cut are traced by holding the square on the opposite side.

The stringer in this example has two pieces of tread stock. This allows for a slight overhang. There is also a space in between the boards. The bottom of the stringer must be cut to the thickness of the tread. This step is called dropping the stringer. After one stringer is cut this piece becomes the pattern that is traced onto the remaining stringers.

Use in roof framing

There is a table of numbers on the face side of the steel square; this is called the rafter table. The rafter table allows the carpenter to make quick calculations based on the Pythagorean theorem. The table is organized by columns that correspond to various slopes of the roof. Each column describes a different roof inclination (pitch) and contains the following information

This table shows five different types of rafter calculations and one table for marking an angle called the side cut or cheek cut

This is a common rafter with the two different cuts. The plumb cut fits in the ridge board and the Bird's mouth fits on the wall plate.

Common rafter per foot of run The common rafter connects the peak of a roof (the ridge) to the base of a roof (the plate). This number gives the length (hypotenuse) of the common rafter per twelve units of horizontal distance (run).

Hip or valley rafter per foot of run The hip or valley rafter also connects the ridge to the plate, but lies at a 45-degree angle to the common rafter. This number gives the length of the hip or valley rafter per seventeen units of run.

Difference in lengths jacks The jack rafters lie in the same plane as the common rafter but connect the top plate (the wall) or ridge board to the hip or valley rafter respectively. Since the hip or valley rafter meets the ridge board and the common rafter at angles of 45 degrees, the jack rafters will have varying lengths when they intersect the hip or valley. Depending on the spacing of the rafters, their lengths will vary by a constant factorhis number is the common difference.

This angle can be cut on the fly by aligning this given number on the blade of the steel square and the twelve-inch mark on the tongue, and drawing a line along the tongue.

Cutting hip and valley criple rafters are all cut in a similar way.

The relationship between hip, jack and common rafters, and how they tie into the ridge and bottom plate. The rafters are fastened to the horizontal ridge board at the peak of the roof.

The side cut is the beveled angle of the hip or valley rafter that fits into the ridge board in this image.

Common and jack rafters all use twelve as the common reference to mark the plumb cut.

Hip and jack rafters use twelve as a common reference while aligning the desired pitch in the side cut column.

Hip and valley rafters use seventeen as the common reference for marking the plumb cut of a rafter.

Use of the octagon scale

Octagon Table located on the front side of the Steel square.

Octagon table viewed from an aluminum square.

Octagon made from the Octagon scale. A protractor can accomplish the same task.

Use of the Diagonal scale

This is the location of the diagonal scale on the square.

The diagonal scale gives the diagonal, or the hypotenuse, for the different legs of the triangle for which a brace is to be cut.

Using calculators in roof framing

There is good reason to use calculators that have verified calculations. Construction calculators use rise and run to calculate lengths and angles. Some are programmed to calculate all side cuts for hip, valley and jack regular rafters to be exactly 45 for all rafter pitches. The rafter table is expressed in inches, and the higher the numerical value of the pitch, the greater the difference between side cut angles within a given pitch. Only a level roof, or a 0 pitch will require a 45 angle side cut (cheek cut) for hip and jack rafters.

Side cut hip/valley rafter table

If a right triangle has two angles that equal 45 then the two sides are equidistant. The rafter is the hypotenuse and the legs or catheti of the triangle are the top wall plates of the structure. The side cut is located at the intersection of the given pitch column and the side cut of the hip/valley row. The regular hip/valley rafter runs at a 45 angle to the main roof and the unit of measurement is 12inches of run. Regular hip/valley and jack rafters have different bevel angles within any given pitch and the angle decreases as the pitch increases.

Legend

c= hypotenuse

P= pitch

L= rafter length

Z= difference in L of jack rafter 16" OC

The side cut of the hip/valley rafter = (Tangent)(12) = side cut in inches. The side cuts in the rafter table are all in a base 12. The arc tan can be determined from any given pitch. Most power tools and angle measuring devises use 90 as 0 in construction. The complementary angles of the arc tan are used with tools like the speed square.

Side cut of jack rafters

The side cut is located at the intersection of the side cut of jack rafters row and the pitch column on the Steel square. There is a row for the difference in length of jacks, 16 and 24inch centers on the blade. The tangents are directly proportional for both centers.

The tangent is in a base 12. The tangent x 12 = side cut of jack rafters. This corresponds to the side cut on the Steel square. The complementary angles of the arc tan are used on most angle measuring devises in construction. The tangent of hip, valley, and jack rafters are less than 1.00 in all pitches above 0. An eighteen pitch has a side cut angle of 29.07 and a two pitch has a side cut angle of 44.56 for jack rafters. This is a variation of 15.5 between pitches.

Plumb cut of jack & common rafters

The plumb cut for jack and common rafters are the same angles. The level cut or seat cut is the complementary angle of the plumb cut. The notch formed at the intersection of the level and plumb cut Is commonly referred to as the bird mouth .

Plumb cut of hip/valley rafters

The plumb cut of the hip/valley rafter is expressed in the formula. The level cut is the complementary angle or 90 minus the arc tan.

Irregular hip/valley rafters

Irregular hip valley rafters run at random angles to the ridge except 45. The top plates can be 90 at the outside corners or various other angles. There are numerous irregular h/v roof plans. The Steel square is applicable for regular hip/valley and jack rafters and not for irregular roofs.

irregular hip/valley gable roof plan.

irregular roof plan.

Intersecting irregular hip/valley gable roof plan.

Carpenter's square

In carpentry, a square or set square is a guide for establishing right angles (90 angles), usually made of metal and in the shape of a right triangle.

See also

Try square

Combination square

Speed square

Steel square

Hip Roof

Bibliography

Siegele, H.H. (1981). The Steel Square. Sterling Publishing. ISBN 0-8069-8854-1.

Ulrey, Harry F. (1972). Carpenters and Builders Library. No.3. Theodore Audel.

Schuttner, Scott (1990). Basic Stairbuilding,. Taunton Press. ISBN 0-942391-44-6.

Spence, William P. (2000). Constructing Staircases Balustrades & Landings. Sterling Publishing.

Gochnour, Chris (February 2006). "11 Essential Measuring and Woodworking Tools". Fine Woodworking (Taunton Press) (182): 75.

Lanham, Wm.. The Steel Square. Bath: E. A. Lovell.

Falconer, John (1925). Ednie, John (editor). ed. The Steel Square. Carpentry and Joinery. Vol. V. Gresham.

Categories: Woodworking measuring instruments | Dimensional instruments

by: gaga

POST COMMENT

Vantec - China Playground Zoo Series - China Playground Nature Series When Will China Be Able To Bid Farewell To The "edison Of The Times" Sunward Bauma 2010 Show Excellent Debut Widely Sought After - China Arm Splint - Thumb Splint Dodge Wc Series - China Black Marble Texture - Marble Texture Manufacturer Taupe - Asg-b Handhold Ecu Timing Signal Generator - China Xdectm Ecu Endocrine Gland - China Foot Splint - Arm Splint Machine Components Industry In China Problems And Their Causes - The Machinery, Basic Parts - China Should Take The Initiative To Adjust Its Own Iron Ore Demand - Multifunctional Drilling Rig The Post-quota Era Ushered In The Development Of China Sewing Machinery Industry Opportunities Connectors And Cable Assemblies Manufactured In China Shahada - Arm Splint Manufacturer - China Foot Splint Hon Hai Investment Of Billions Of Nt Dollars To Be Built In China 10 000 3c Chain Stores - Hon Hai Overview Of World-wide Collecting Robots - Robots - Machinery Industry - China Violet Laser